For brake controller installation in Bunbury we fit electric brake controllers, 7-pin and 12-pin trailer plugs and Anderson plugs, and we check the breakaway system while we're there. Everything goes in on a dedicated loom or a vehicle-specific module, never spliced into the factory harness, because the Department of Transport WA warns that splicing can damage the vehicle's electrics.
We fit gear from Redarc, Projecta and Narva where it suits your vehicle and trailer, and we test the lot hitched up before you drive away. It's the sort of job where a missed detail shows up on the highway, so we do it properly in your driveway. Call 08 6706 6760 or send the quote form for a free quote.
Towing electrics we fit
Most towing jobs involve four things: the brakes, the plug between car and trailer, the charging feed to the van or camper, and the breakaway. Here is how we handle each one on vans, boat trailers and horse floats around Bunbury.
Electric brake controllers
An electric brake controller sits in the cab and tells the trailer's electric brakes how hard to work. Proportional controllers sense how hard the vehicle is slowing and match it. Time-based controllers apply a set amount over a set time.
We mount the unit where you can reach it, wire it with a proper fused feed, and set it up for the weight of your trailer.
7-pin and 12-pin trailer plugs
Trailer plugs come in flat and round styles, and the two don't mate without an adaptor. A 7-pin plug carries the basic lighting circuits and the signal for the brakes. A 12-pin flat plug adds extra pins, including a permanent 12V feed for charging the van's battery and a reversing light circuit.
For 7-pin trailer plug wiring or 12-pin trailer wiring, we wire the vehicle socket to suit your trailer and fit an adaptor when the plugs don't match.
Anderson plugs for charging
An Anderson plug is a heavy-duty two-pole connector that carries charging current from the tow vehicle to a van or camper battery. The thin wires in the trailer plug can't carry that much current. So Anderson plug installation means a separate heavy cable from the car's battery or DC-DC charger to a plug at the towbar, fused at the source. That keeps the fridge cold and the van battery topped up on the road.
Breakaway systems
A breakaway system is a small battery-powered unit that applies the trailer brakes straight away if the trailer detaches from the car. In WA, on a trailer over 2,000 kg GTM, the brake system has to apply the brakes immediately if the trailer comes loose.
We fit the breakaway switch, cable and battery, check the lanyard is routed so it pulls the pin cleanly, and test that it applies the brakes. A flat breakaway battery is a common reason for it to fail, so we check that too.
How we wire a vehicle for towing
Towbar wiring in Bunbury runs in four steps, and the order matters. We start with what you tow and finish by testing the lot while it's hitched up.
- 1
Check the trailer and vehicle
We start with the trailer's gross trailer mass (GTM), its brake type and its plug. Then we look at what wiring the tow vehicle already has, and whether the sockets match. That tells us whether we need a full loom or a plug-in module, and whether the trailer needs work before it's towed.
- 2
Run a dedicated loom
We use a towing loom or a vehicle-specific module and route it clear of heat, exhaust and moving parts. We don't splice into the factory harness. Connections are crimped, sealed and fused where they need to be, and the cable is clipped so it can't chafe on the body.
- 3
Fit and set the controller
We mount the controller where the driver can reach it, wire it to a fused supply and the brake light signal, and set the gain for your trailer. A loaded van needs a different setting from an empty boat trailer. We also show you how to adjust it for your next load.
- 4
Test lights and brakes hitched
With the trailer connected we run every light function: tail, brake, indicators and reverse. Then we apply the brakes and confirm the trailer's brakes work with the controller, and check the breakaway and any charging feed. You see the results before you leave.
Want the fault found and the repair priced before any work starts?
Towing rules in WA and brake controller installation in Bunbury
Towing rules in Western Australia are set by the Department of Transport WA, and they apply the same in Bunbury as anywhere else in the state. A trailer of 750 kg gross trailer mass (GTM) or more must have brakes unless the department approves otherwise. Above 2,000 kg GTM, brakes are needed on all wheels and over-run brakes can't be used.
On those heavier trailers, the brake system must also apply the trailer brakes immediately if the trailer comes loose. Safety chains are needed too: at least one for trailers under 2,500 kg ATM, and two from 2,500 to 3,500 kg. The department also advises checking the trailer lights every time you hitch up.
Vans, boat trailers and horse floats leaving Bunbury can use the Wilman Wadandi Highway, a 27 km four-lane road that opened in December 2024. Working brakes and lights matter on every one of those runs.
Towing wiring done right
Here is what you get when the job is finished and the trailer is hitched up.
No splicing into the vehicle harness
The Department of Transport WA warns that splicing trailer lights into the vehicle's wiring harness may damage the vehicle's electrical system. So we don't. We use a dedicated towing loom or a plug-in module made for your vehicle, run the power from a fused supply, and leave the factory wiring as it was.
Brakes set to the load
A controller set for the wrong weight either locks the trailer wheels or does too little. We set the controller gain for your trailer, then adjust it with the van or boat loaded the way you normally tow. You'll know how to change it for a lighter load, and what to listen and feel for if it needs another tweak.
Everything tested hitched up
Before you drive off we check every light function, the brake output, the breakaway and any charging circuit with the trailer connected. Problems show up on a hitched rig, not on a bench. If something isn't right, we fix it before we hand the keys back. A short test drive is part of the job where the trailer allows it.
What affects the cost of fitting a brake controller?
Four things move the cost of a towing job: the controller, the state of the vehicle's wiring, the plugs and what's needed on the trailer. We give you a free quote once we know your setup.
Controller type
Proportional controllers cost differently to time-based ones. In-dash units and remote-mounted units also need different fitting time, and the mounting spot matters.
Vehicle wiring
A vehicle with factory towing wiring is a shorter job. One with no wiring at all needs a full loom run from the back to the cab.
Plug types
A 7-pin socket is a simpler job than a 12-pin. Adding an Anderson plug or an adaptor changes the parts and the time.
Trailer work
Old or corroded wiring on the trailer side, or a missing breakaway, adds work. We look at the trailer when we quote.
Brake controller and trailer wiring FAQs
Can you install an electric brake controller yourself?
You can install an electric brake controller yourself, but the wiring, mounting and set-up all affect how well it stops the trailer. A poor connection or the wrong gain setting can leave the trailer brakes too weak or too harsh. Many people book a fitter so it's done once and tested hitched up.
What affects the cost of fitting an electric brake controller?
The cost of fitting an electric brake controller depends on the controller you choose and the wiring already in your vehicle. Plug type and the condition of the trailer wiring also play a part. Send the quote form with your vehicle and trailer details and we'll price it without charge.
Can I tow a trailer with electric brakes without a brake controller?
No, you can't tow a trailer with electric brakes without a brake controller, because the trailer's brakes won't work. Nothing in the car creates the signal that tells them to apply. In WA, trailers of 750 kg GTM or more must have working brakes.
Do I need a brake controller if I have a 7-pin trailer plug?
Yes, you still need a brake controller with a 7-pin trailer plug, because the plug only carries the signal and doesn't create it. The controller reads how the vehicle is slowing and sends the brake output through the plug. A plug with no controller behind it leaves the trailer brakes dead.
Will a brake controller drain the battery?
A brake controller won't drain the battery when it's wired correctly, because its standby draw is very small. Problems show up when it's connected to a permanent supply that's been badly done, or when a faulty unit stays switched on. We wire the feed properly and check for draw during the final test.
When does a trailer or caravan need brakes in WA?
A trailer or caravan in WA needs brakes once its gross trailer mass reaches 750 kg, unless the Department of Transport approves otherwise. Over 2,000 kg GTM, brakes are needed on every wheel, and the brake system must also apply the trailer brakes if the trailer detaches.