Mobile auto electrician across Bunbury, Australind, Eaton & DalyellupCar won't start? Call 08 6706 6760
BunburyMobile Auto Electrician
Menu

HomeServicesMarine Electrical

Marine Electrician in Bunbury, WA | Boat 12V Repairs & Fit-Outs

The boat won't start at the ramp. The bilge pump didn't run after the last rain. The nav lights are out and the sun is going down. These are the faults a marine electrician sorts out around Bunbury, and as a mobile auto electrician in Bunbury we come to you and trace them. We start with the battery and work outward, because a flat start battery is often a symptom of a fault further along.

We work on the 12V electrics of trailer boats and small craft: batteries and battery switches, bilge pumps, navigation lights, fish finders and the wiring that feeds them. Salt is hard on all of it. It gets into terminals and cable ends, and it can eat copper from the inside.

We replace failing wiring with marine-grade parts and fit gear from Redarc, Projecta and Victron where it suits the boat. We don't do 240V shore-power work, and we say so up front. Call 08 6706 6760 or send the quote form for a free quote.

Boat electrical work we do

Most boat electrical jobs fall into five groups, from the batteries up to the electronics on the dash. Each one below is mobile marine electrics work we do on boats kept on trailers, in pens or on moorings around Bunbury.

Batteries and battery switches

A boat needs a start battery for the engine and often a second for the house loads, such as lights and a fish finder. We fit battery switches so you can isolate each one, and we fit a boat dual battery setup so the start battery is never run flat by the accessories.

A new battery on old, corroded leads will still fail, so we replace the leads too. If the boat has sat for weeks, we also check the charge and that the switch isolates the circuits cleanly, since a small drain can flatten a battery between trips. Day boats and overnight boats need different setups, and we plan around how you use yours.

Bilge pumps and float switches

The bilge pump has to work when you aren't there. We wire the pump on its own fused circuit, fit an automatic float switch so it runs as the water rises, and add a manual override at the helm. Then we test it by running the pump and lifting the float, so we know it works before you rely on it.

A pump that is wired straight to the battery with no fuse is a fire risk, and a pump with a corroded connection fails quietly. We fix both, and we show you where the switch is so you can check it before each trip.

Navigation and deck lights

Navigation lights tell other boats where you are and which way you're heading. We repair or replace the red and green bow lights and the stern light, fit anchor lights, and add LED deck lights for working at night. LEDs draw far less current than old bulbs, which is easier on a small boat's battery.

Every fitting is sealed against spray and rain. If a light has failed, we check the socket and the supply before replacing the lens, because the fault is often the wire behind it and not the globe or LED.

Electronics power

Fish finders, chartplotters and VHF radios all need clean power. We run each one from a fused feed with a neat, sealed connection, so voltage dips from a shared or overloaded circuit don't reset the screen or drop out your radio.

Cables are routed away from sharp edges, moving parts and the bilge, and left with a little slack so nothing pulls on a plug. Where the boat has no spare fuse or breaker position, we add a small panel so each device has its own protected circuit and can be switched off alone.

Corroded wiring and connections

Green, crusty terminals and stiff, blackened cable are signs of salt corrosion. The corrosion creeps up the strands inside the insulation, so a joint that looks fine can still be failing. We cut back to clean copper and replace connections with tinned lugs and sealed terminals, or rewire the circuit when the damage runs too far to repair.

We also look for the cause, such as a leaking hatch, a wet cable run or a missing drip loop, so the same corrosion doesn't come back in a year.

How we approach a boat electrical job

A boat is not a car with a hull around it, and we treat the job that way. The steps below are how a typical repair or fit-out runs from first question to final test.

  1. Find out how the boat is used

    Day trips and overnight stays need different setups. We ask what's on board, how long you're out, and what keeps failing, then plan the work around that. A boat that sits on a mooring is a different job from one that's trailered home and rinsed after every trip.

  2. Test batteries and circuits

    We check battery charge and cranking, measure voltage drop along the cables, and look at each circuit for corrosion. That finds the real fault before we replace anything. Often it's a corroded earth or a tired terminal, not a dead battery, and a voltage-drop test shows that in minutes.

  3. Repair with marine-grade parts

    We use tinned cable, sealed heat-shrink connectors and the right fuse or breaker on every circuit. Plain copper and cheap crimps don't last in a salt environment, so we don't use them. Anything corroded comes out, and the new run is clipped clear of the bilge.

  4. Test on the trailer or water

    Before hand-back we run every circuit: pump, lights, electronics and charging. If the boat is on its trailer, that's where we test it. Otherwise we test it where it sits, and we show you the switches and fuses so you know what each one does.

Want the fault found and the repair priced before any work starts?

Boating around Bunbury and why it needs a marine electrician

Casuarina Boat Harbour has a two-lane ramp, parking for vehicles and boat trailers, and a slipway. The harbour also has 52 recreational and 5 commercial pens, swing moorings and a service jetty where diesel is available.

The ramp has no wash-down facilities. That matters for electrics: salt water sits on the trailer's lights and plugs and on the boat's connectors until someone hoses them down at home, and that is how terminal corrosion starts.

Koombana Bay changed in February 2025, when the Department of Transport adjusted on-water rules after a new 460 m northern breakwater was built at the harbour. The smaller ski area, adjusted 5 and 8 knot zones and new navigation aids all affect how and where people run their boats. Bunbury itself sits at the southern end of the Leschenault Inlet, which opens to Koombana Bay and Geographe Bay.

Built for salt water

Boat electrics fail where the salt gets in, so the work is built to keep it out.

Marine-grade materials

Tinned copper cable resists the corrosion that eats ordinary wire in salt air. We pair it with sealed, heat-shrink connectors and tinned lugs so moisture can't wick up the strands. Terminals and fittings are chosen for a marine environment, not a dry engine bay. That is how a repair keeps going past the next few trips.

Circuits fused and labelled

Every circuit is protected at its source, close to the battery, with a fuse or breaker sized to the cable and the load. We label each circuit on the panel so you can find the bilge pump, lights or electronics in a hurry. If something trips, you know where to look.

Boat trailer lights

Trailer lights get dunked every time the boat goes in. We fit submersible LED lights and sealed plugs, and check the earth connection that so often corrodes first. A bad earth makes every light on the trailer dim or flicker. Brakes, plugs and the tow vehicle's side of the wiring are covered on our boat trailer wiring and brake controllers page.

What affects the cost of boat electrical work?

Boat jobs vary more than car jobs, mostly because of access and how far the damage has spread. We look at the boat, ask about use, and give you a free quote.

Boat size and access

A small tinny console is quick to reach. A cabin boat with tight hull spaces takes longer to work in.

Corrosion extent

A few bad terminals are a spot repair. Wiring corroded through the strands may mean replacing the whole run, not just the ends.

Batteries

A single battery with a switch is simpler than a dual battery setup with a charging link and extra fusing.

Electronics

Each fish finder, chartplotter or radio adds a fused feed and cable run, so the number of devices changes the job.

Marine electrical FAQs

What is a marine electrician?

A marine electrician is a tradesperson who works on the low-voltage electrics of boats, including batteries, pumps, lights and electronics. It differs from household electrical work, because boat systems run on 12V DC and have to survive salt, vibration and damp. As a marine auto electrician, we cover the 12V side of boat electrics.

How do I set up a dual battery on a boat?

To set up a dual battery on a boat, you fit a start battery and a house battery and join them through a battery switch or a voltage-sensitive relay. The relay lets the engine's alternator charge both batteries but keeps them separate when the engine is off. Cabling and fusing are sized to the loads.

Can you put solar panels on a boat?

Yes, you can put solar panels on a boat as long as they feed the battery through a solar regulator, which stops overcharging. Mounting position and shading both affect output, so we plan where the panel sits and route the cable through a sealed entry.

Can I have 240V on my boat?

Yes, a boat can have 240V power through an inverter or shore power, but fixed 240V wiring must be done by a licensed electrical worker. In WA, Building and Energy says 240V wiring in vehicle conversions must only be carried out by a licensed electrical worker employed by a licensed electrical contractor. We handle the 12V side only.

Can you rewire the lights on my boat trailer?

Yes, we can rewire the lights on your boat trailer, and we fit submersible LED lights and sealed plugs. Trailer lights fail after salt water because moisture gets into plain connectors and corrodes the wiring and earth. Sealed fittings keep that water out.

Boat electrics playing up? Call before the next launch

A slow pump, flickering lights or a start battery that won't hold a charge are all worth testing before the next launch. Ring 08 6706 6760 or send the quote form with a description of the boat and what it is doing.