A dual battery installation and 4WD electrical fit-out covers the auxiliary battery, DC-DC charger, correctly sized wiring, fridge outlets, driving lights, UHF radio and cameras, all planned around how you travel. We mount it in the tray, the canopy or under the bonnet, and we fit gear from Redarc, Enerdrive, Projecta, Victron and Narva where it suits the setup.
We start by finding out what you run and how long you stay out, then build the system to suit. That avoids paying for capacity you will not use, and it avoids a battery that is too small for the fridge you already own.
Need a 4WD auto electrician in Bunbury before a trip? Tell us the vehicle, the fridge and the gear you run on 08 6706 6760 or through the form, and the quote is free.
4WD and dual battery fit-outs we do
Most touring setups are a mix of a few jobs. Here is what we fit, and how each part earns its place in a 4WD, ute or tow vehicle.
Dual battery systems
A dual battery system adds an auxiliary battery that runs the fridge and accessories, so the start battery stays untouched. A dual battery kit usually means the battery, a tray, a charger and cabling. We fit it under the bonnet, in the tray or in the canopy, depending on space and cable run.
The battery is charged either through a battery isolator or a DC-DC charger. An isolator is simple and suits older vehicles. A DC-DC charger gives the auxiliary battery a controlled charge from the alternator, which is better for most newer setups.
DC-DC chargers
Many modern vehicles use smart alternators that drop their output voltage once the start battery is full. A basic isolator then leaves the auxiliary battery undercharged. A DC-DC charger lifts that voltage back to what the battery needs.
Most units also take a solar input through an MPPT regulator, so the panels and the alternator charge through one device. For DC-DC charger installation we use brands such as Redarc and Enerdrive, sized to the battery and the cable run.
Fridge power and 12V outlets
In a dual battery setup for a fridge, the fridge is usually the biggest steady load, so it gets its own fused circuit sized for the run from the battery. A thin cable drops voltage and starves the compressor.
We add Anderson plugs for trailers and portable panels, plus 12V and USB sockets where you will use them. Outlets sit on their own fused circuits and are labelled, so a fault in one never takes the fridge down with it.
LED light bars and driving lights
Light bars and driving lights draw serious current, so we wire them through a relay and a fuse, with a switch inside the cab. Running them off a light switch cable alone can melt connectors.
WA rules limit you to four additional driving lights, and they must switch off when the high beam does. We wire to that rule from the start.
UHF radios and reversing cameras
A UHF radio performs best with the aerial mounted where it has a clear metal ground plane, and with clean power straight from a fused supply. We place the aerial, run the coax without kinks and tune the SWR.
For reversing camera installation and dash cams, we run power and video leads through the body without chafe points, so the camera still works after a season of corrugations.
How we plan and fit a dual battery system
Every fit-out follows the same four steps, so the system matches what you carry and how long you stay out.
- 1
Work out your power use
We start by listing what you run: the fridge, lights, phone and laptop charging, and how many days you spend off-grid. Those loads set the battery capacity, the charger size and the cable gauge, so nothing is guessed.
- 2
Choose battery and charging
Next we choose between an AGM or lithium battery, and between an isolator and a DC-DC charger. If you want solar, we plan the input at this stage so the charger, regulator and battery all work together.
- 3
Fit and wire
We use cable sized for the current and the distance, fuse each circuit at the source, and mount the battery on a proper tray or bracket. Looms are protected against heat and chafe, and joins are crimped and sealed.
- 4
Test and show you
We test that the battery charges while the engine runs and that every circuit works. Then we set up the battery monitor and show you how to read it, so you know your state of charge before a long stretch off-grid.
Want the fault found and the repair priced before any work starts?
AGM or lithium?
Two battery types suit most auxiliary setups. Each has real strengths, and the right pick depends on weight, budget and how hard you cycle it.
AGM auxiliary battery
An AGM battery costs less upfront and is a proven choice for a fridge and a few accessories. It is heavier than lithium, and deep, repeated discharges shorten its life, so only part of its rated capacity is really usable.
It also charges more slowly in the final stages. For weekend trips and modest loads, it is a sensible and affordable option.
Lithium (LiFePO4) auxiliary battery
A lithium (LiFePO4) battery is much lighter and lets you use more of its rated capacity. It also holds its voltage under load, which suits fridges and inverters. The trade-off is a higher upfront cost.
Lithium also needs the right charging profile and a battery management system (BMS) that protects the cells. That is why a DC-DC charger usually goes in with a lithium battery. We match the charger to the battery.
Dual battery installation in Bunbury for South West trips
Bunbury is a natural jump-off for touring. Forrest Highway runs north about 96 km towards Perth, and the Wilman Wadandi Highway, which opened in December 2024, now links it through to Bussell Highway for the run south.
Long highway runs at load show up weak charging and marginal wiring quickly, so it pays to test the system before you leave rather than on the side of the road.
Driving lights are a common add-on for night driving in the South West, and WA's Information Bulletin IB-132D sets the limits: up to four additional lights, off when the high beam is off, and used only when no vehicle is within 200 metres ahead.
If you want a fixed 240V circuit off an inverter, that part must be done by a licensed electrical worker employed by a licensed electrical contractor in WA. We stay on the 12V side and tell you plainly where that line sits.
Fit-outs that survive corrugations
Corrugated tracks shake loose anything that is not fitted properly. Here is what we do so your setup holds up and is safe to use.
Secure mounting
A battery is heavy, and on a rough track it becomes a projectile if it is not held down. We use trays and brackets that suit the battery size and bolt them to solid structure, not thin panel steel.
Terminals are covered, and the battery sits where a leak or vent cannot reach anything sensitive. We check mounts again after the first test so nothing has moved.
Correct cable and fusing
Undersized cable drops voltage, heats up and can start a fire. So the cable gauge is chosen for the load and the distance, and every circuit gets a fuse right at the battery.
That protects the wiring, not just the gear on the end of it. Anderson plugs, joins and lugs are crimped properly and sealed against moisture and dust.
Legal lighting
Extra lights need to follow the WA rules to be legal on the road. We wire light bars and driving lights to switch off with the high beam, as IB-132D requires.
Once the job is finished we check the switching in the cab: lights on with the high beam, and off without it.
What affects the cost of a dual battery setup?
No two fit-outs are the same, so we quote after we know what you carry and how you travel. These are the main factors, and our free quote covers each one.
Battery chemistry
AGM costs less upfront, while lithium costs more but is lighter and gives more usable capacity. The right choice depends on your loads and how often you head out.
Charger type
A simple isolator costs less than a DC-DC charger. Adding solar input or a larger charger raises the cost, but it suits smart alternators and bigger batteries.
Location
Under the bonnet is the shortest run. A tray or canopy needs longer cable, extra protection and sometimes a separate mounting, which adds labour and material.
Accessories
Outlets, a battery monitor, light bars, a UHF radio and cameras each add parts and wiring time. Tell us what you want, and we will itemise it in the quote.
Dual battery and 4WD electrical FAQs
Do I need a DC-DC charger for a dual battery system?
Many dual battery systems in modern vehicles need a DC-DC charger. Smart alternators drop their voltage once the start battery is charged, so a basic isolator can leave the auxiliary battery undercharged. A DC-DC charger fixes that, and it is close to essential with a lithium battery.
How does a dual battery get charged?
A dual battery is charged from the alternator through either a battery isolator or a DC-DC charger. It can also take charge from solar panels through a regulator. Many setups combine the alternator and solar, so the battery gets charge both when driving and when parked.
How long will a dual battery run a fridge?
How long a dual battery runs a fridge depends on the battery's usable capacity, the fridge's draw, and the outside temperature. A hot day in a closed vehicle makes the compressor run more. We size the battery to your fridge and your days off-grid, so you get a realistic answer for your setup.
What are the benefits of lithium batteries compared to AGM?
Lithium batteries are lighter and give you more usable capacity than AGM, and they hold voltage better under load. They need a compatible charger and a BMS, and they cost more upfront. AGM is cheaper and proven, but heavier, and it should not be drained as deeply.
Can I install more than one auxiliary battery?
Yes, you can install more than one auxiliary battery, as long as the batteries are matched and the charging is set up for the whole bank. Mixing old and new, or different types, causes uneven charging and shortens battery life. We size the charger and cable for the full bank.
Are LED light bars legal in WA?
LED light bars are legal in WA when they follow Information Bulletin IB-132D. You can fit up to four additional driving lights, including light bars, and they must stay off when the high beam is off. They may only be used when no vehicle is within 200 metres ahead.
Can I fit out my 4WD with 12V electrics myself?
You can do some of it yourself, such as plugging in portable gear. Fused circuits, correct cable sizing and charging setups are where most DIY jobs go wrong. Anything involving 240V is different, because in WA it must be done by a licensed electrical worker.