Mobile auto electrician across Bunbury, Australind, Eaton & DalyellupCar won't start? Call 08 6706 6760
BunburyMobile Auto Electrician
Menu

HomeServicesCar Electrical Repairs & Diagnostics

Car Electrical Repairs in Bunbury, WA | Fault Finding & Diagnostics

Some electrical faults come and go. A warning light switches itself off then returns, the central locking works on Tuesday and not on Wednesday, or the battery is flat every Monday after sitting all weekend. Those faults waste time and money because a part gets replaced and the problem is still there, or it comes back a fortnight later.

We handle auto electrical repairs in Bunbury by finding the cause before anything is replaced, so your car electrical repairs in Bunbury are done right the first time. That means starting with the symptoms, not the parts catalogue.

Our approach combines fault codes, meter readings and physical wiring checks. A scan tells us where to start, a multimeter tells us what the circuit is doing, and a look at the earths, connectors and looms tells us why. We work on cars, utes and 4WDs, and we explain what we found in plain terms, including what is urgent and what can wait.

Nothing is replaced on a hunch. If the fault only shows up under certain conditions, we test it under those conditions before we call it fixed. If you've been searching for car electrical repair near me, call 08 6706 6760 or send the quote form and describe when the fault happens.

Car electrical faults we find and fix

Car electrics cover everything from the starter circuit to the central locking. Here are the faults we are asked about most, and how we approach each one.

No-start and no-crank faults

A car that cranks but won't start, clicks and does nothing, or starts then dies each points to a different part of the circuit. We test the battery first, then follow the starting circuit through the cables, relays and solenoid. On modern cars the immobiliser can also stop an engine from running, so we check that the key and the security system are talking to each other. Cranking faults and fuel or ignition faults are separated before any parts are replaced.

Battery drain

A battery that goes flat overnight or after a weekend usually has a circuit that stays awake when it shouldn't. We run a parasitic draw test with a meter on the battery and then pull fuses one at a time to find the circuit responsible. The cause is often a stuck relay, an aftermarket accessory or a module that never goes to sleep. Once we find the circuit, we repair it properly rather than disconnecting the battery each night.

Warning lights and computer faults

We read the fault codes with an OBD scanner and then test the sensor, wiring or connector the code points to. A warning light can come from a damaged wire or a corroded plug rather than a failed ECU. Where a fault needs a module replaced and programmed to the vehicle, we tell you it is dealer work. We don't claim dealer-level tools, and we don't guess at expensive parts.

Lighting faults and upgrades

A headlight that keeps blowing globes, a dim tail light or an indicator that flashes too fast is rarely just the globe. We check the globe, the wiring, the connector and the earth in that order, because a poor earth is a common cause of lighting faults. We also fit driving lights and lighting upgrades with the right relay, fuse and harness, so the new load doesn't overload the original wiring or the switch behind the dash.

Locks, windows, alarms and immobilisers

Central locking that works on one door, a power window that stops halfway and an alarm that sets itself off all come down to wiring, switches, actuators or a control unit. We test each circuit rather than replace the first part that looks suspect. Faults with aftermarket alarms and immobilisers are common, and we can trace those too, including wiring problems left behind by earlier installs, such as an alarm tapped into the wrong circuit.

How we track down an electrical fault

Fault finding is a sequence, not a guess. We work through these four steps so the repair fixes the cause and not just the symptom.

  1. Listen to the symptoms

    We ask when the fault happens, how often, and what changed recently. A fault that appears in the rain, on cold starts or after a new accessory went in tells us where to look first. Notes, photos and a description of the warning lights all help.

  2. Scan and test

    We read the OBD codes, then test the battery and charging system before touching anything else. We also measure voltage drop across the main cables and earths, because a connection that looks fine can still be losing power under load.

  3. Trace the circuit

    With the wiring diagram and a meter, we follow the circuit through fuses, relays and connectors, one section at a time. We look for corrosion, loose pins and looms that have chafed or been damaged by earlier repairs, and we test each section before moving on.

  4. Repair and prove it

    We fix the cause, clear the codes and re-test under the conditions that brought the fault on. If it only happened when the car was wet or hot, we test it that way before we hand it back, so you aren't the one finding out it isn't fixed.

Want the fault found and the repair priced before any work starts?

Car electrical repairs for Bunbury conditions

Bunbury gets 737.3 mm of rain a year, most of it from May to September, and mean 3pm humidity climbs to 64 to 66 per cent from June to September. Damp gets into connectors and fuse boxes, so winter is when intermittent faults and corroded terminals show up.

Bunbury sits at the southern end of the Leschenault Inlet, where it opens to Koombana Bay. For a car parked near the water, salt can work into earth straps, battery terminals and exposed plugs, and slowly raises resistance until something misbehaves.

July mornings have a mean minimum of 7.4 °C, and that is when a tired battery gives up. Cars used for short trips around town never fully recharge, so slow cranking is a common winter complaint.

Repairs that last

An electrical repair is only as good as the joins, fuses and protection behind it. This is what we do so a fix stays fixed.

Proper joins and protection

Wires are joined with soldered or crimped joints covered in heat-shrink, not twisted together and taped. Where water can get in, we use sealed connectors and keep the loom supported so it can't chafe. Joins made this way handle heat, vibration and a wet winter without turning green or going open circuit.

Correct fuses and circuits

Every circuit gets a fuse rated for the wire it protects. We never bypass a blown fuse with a bigger one or a bit of wire, because that moves the failure from a fuse to the loom. If a fuse keeps blowing, something is wrong downstream, and finding it is the job.

Explained at handover

When we hand the car back, we tell you what failed, why it failed and what was replaced. If something else is nearing the end of its life, such as a tired battery or a perished cable, we point it out and leave the decision to you. You get the facts and a clear picture of what the car needs.

What affects the cost of car electrical repairs?

Electrical faults vary a lot, from a corroded earth to a failed module, so we quote each auto electrical service after we have looked at it. These are the main things that decide the cost. Ask for a free quote and describe the fault.

Time to trace the fault

An intermittent fault takes longer to catch than one that is there every time, and the time spent tracing it affects the price.

Access

Getting to a wire behind the dash or inside a door trim takes longer than one in the engine bay.

Parts

A relay or fuse costs far less than a control module, and some parts must be ordered in, which adds time.

Vehicle type

Older vehicles have simpler circuits. Modern networked cars need more testing and sometimes programming that only a dealer can do.

Car electrical repair FAQs

Why will my car not start?

A car will not start because of a flat or failed battery, a faulty starter motor, a security or immobiliser problem, or a fuel or ignition fault. We start by load testing the battery and checking the cables, then test the starter and read any stored codes. That sorts the cause before any parts are replaced.

Why does my car crank but not start?

A car that cranks but won't start has a working battery and starter, so the fault is somewhere else. We look at fuel delivery, ignition, crank and cam sensors, and whether the immobiliser or ECU is stopping the engine. Fault codes and live readings usually show which one.

Why won't my car start when the battery is fine?

A car won't start with a healthy battery when the power isn't reaching the starter or the starter isn't turning. The usual causes are a faulty starter motor, a failing solenoid, a corroded cable or earth, or an immobiliser fault. We test voltage at the starter while someone turns the key.

Why does my car just click and not start?

A car that just clicks is not getting enough current to the starter. A weak battery, a loose or corroded terminal and a failing starter solenoid are the usual causes. A load test and a voltage check at the starter tell us which.

What causes a car to lose all electrical power?

A car loses all electrical power when the main supply is interrupted, most often a loose or corroded battery terminal, a failed earth strap, a blown main fuse or a worn ignition switch. We check the terminals and earths first, then the main fuse and the switch.

Can a weak car battery cause electrical problems?

A weak car battery can cause a range of electrical problems. Odd warning lights, radio and clock resets, slow cranking and flickering lights are all common. Modern cars are sensitive to low voltage, so we test the battery before chasing faults elsewhere.

Have a fault that keeps coming back?

Tell us what the car does, when it does it and what has already been replaced. Ring 08 6706 6760 or send the form and we'll work out where to start.